Produkty dla do silników (459)

Protech Fix AC-Therm Water-based anti-condensing wall covering, with excellent fixing and anchoring properties, with good coverage based on high penetration acrylic resins, 3M Glass Bubble, pigments, fillers and covering fillers. Suitable as an anti-condensation fixative primer, prior to painting or coating the plaster with anti-condensation paints or plasters (-THERM). Ideal for interventions on walls with mucilage deposits, bacterial phenomena and moulds. Due to its low thermal conductivity, it is particularly suitable for solving mould problems. It can be applied on any plaster (rustic, civil, plaster, dry mortar, plasterboard, concrete, prefabricated, exposed concrete, etc.). Made with special resins and additives it reduces the absorption of the support while allowing the necessary transpiration, uniforms the absorption making the application of the finishing coats easier. It always works in depth, which is why it is the ideal preparation for applying water-based paints or coatings. Adhesion is excellent even on particularly difficult surfaces, thanks to the use of special resins and the presence in the formulation of an adhesion promoter interacting between the support and the product. Preliminary treatment of any surface (civil, plaster, rustic, dry mortars, plasterboard, concrete, prefabricated, exposed concrete etc.) designed to isolate the support surfaces and standardise the absorptions of the subsequent anti-condensate treatments (painting and protective coatings). Packaging: 14-liter bucket UM: €/l

Filtene Fondogiunto Closed cell polyethylene foam kerb, compressible, to properly size the depth of the expansion joints (creation of the "third wall" or base material) before filling them with the polymeric sealants Protech Flex, PROTECH SIGILFLEX MONO or EG 91. It is available in profiles of circular cross-section of different diameter that will fit joints of any shape and size. Suitable for any type of joint between prefabricated elements, infills, bodies of different structures, partitions, doors and window frames, flooring. The insertion of a "joint base" filler material has many functions in both static and expansion joints: sizing the joint in the most appropriate shape and measurements for the characteristics of the sealant to be used, reducing the stresses internal to the sealant itself and on the adhesion to the walls; favouring the contact of the sealant with the side walls during joint filling; reducing sealant consumption. Filling the "joint base" for any type of joint between prefabricated elements, infills, bodies of different structures, partitions, doors and window frames, flooring, prior to laying the elastic sealant in the joint itself. The diameter of Filtene Fondogiunto should be about 25% greater than the width of the joint to allow a stable positioning of the profile and create sufficient resistance to the pressure exerted by the sealant during extrusion. Push with a tool with a rounded tip (free of sharp and pointy edges), capable of crossing the width of the joint, Filtene Fondogiunto, up to the desired depth and so as to leave on the surface an adequately deep seat for the subsequent sealant. Normally the depth of the sealing should be about half the width of the joint. Polyethylene foam is unaffected by solvents contained in the primers, but it is a good idea never to apply the adhesion promoter Protech Flex Primer on Filtene Fondogiunto, in order not to alter the anti-adherence properties. FILTENE can then be inserted into the joint after applying the primer, when the "dust-free time" is attained. A good rule is for the depth of the sealing (adjustable depending on the positioning of Filtene Fondogiunto) not to exceed the width of the joint itself. Confezione: Rotolo da 25 metri UM: €/m

Fluid SRA Concentrated liquid additive formulated to reduce shrinkage in the plastic phases of cement mortar. It reduces shrinkage by over 50% compared to the same mixture without the additive, especially when curing conditions are not possible in a humid environment. Excellent in combination with anti-shrinkage and structural fibers for achieving high structural performance works. It can be used in certain thixotropic and castable structural mortars of the REPAR and GROUT families according to the quantities specified in the respective technical data sheets. For mortars with high volumetric stability. Reduces cracking caused by shrinkage in the plastic phases of cement mortar. Reduction of free air shrinkage in some structural mortars of the REPAR and GROUT families (particularly useful when wet curing conditions for structural mortars are not feasible). Fluid SRA must be added to the mortar after adding the mixing water to the cement mixer. After addition, mix thoroughly before casting. The typical dosage for normal use is approximately 1% relative to the weight of the binders. Packaging: 1 kg bottle UM: €/kg

Consilex ST Transparent penetrating consolidator, for natural stones, ornamental stone elements, mineral plasters and in general for the restoration of cultural heritage. It consists of ethyl esters of silicic acid in solvent, hardening by reaction with atmospheric humidity. It is applied by spraying at low pressure, until the treated surfaces are rejected, in order to guarantee an extremely deep consolidation. Packaging: 5-liter can UM: €/l

Floor Level Floor Level is a self-levelling modified-polymer cement mortar with fibre-reinforcement, offering accelerated grip and fast hardening. Applied prior to laying the flooring, it is perfect for levelling at thickness ranging from 3 mm to 20 mm so as to adapt to any type of covering. Floor Level is a self-levelling modified-polymer cement mortar with fibre-reinforcement, offering accelerated grip and fast hardening. Applied prior to laying the flooring, it is perfect for levelling at thickness ranging from 3 mm to 20 mm so as to adapt to any type of covering. Floor Level is a self-levelling modified-polymer cement mortar with fibre-reinforcement, offering accelerated grip and fast hardening. Applied prior to laying the flooring, it is perfect for levelling at thickness ranging from 3 mm to 20 mm so as to adapt to any type of covering. Packaging: 25 kg bag UM: €/kg

Protech Balcony Solution based on special silane and siloxane resins in solvent, highly penetrating, transparent (colourless), for quickly, effectively and economically waterproofing balconies, tiled terraces, concrete roofings, external stairs, etc., without removing or intervening on the existing flooring. It does not change the appearance of the support on which it is applied and it does not alter the original slipperiness or its water vapour breathability. It is quick to apply and does not require skilled labour or professional equipment. The flooring treated will be usable after only 2 hours of laying. Protech Balcony is a product that is easy and quick to apply: simply spread it out with a scrubbing brush on clean and dry surfaces to solve the problem of infiltration. The active ingredient, effectively conveyed in a solvent, it penetrates fillings, substrate cracks and porosity rapidly and in-depth. Upon contact with air, it performs a polymerisation reaction that seals and waterproofs, perfectly and in depth, all discontinuities where it has managed to penetrate. After the reaction, the specific polymerised siloxane molecule is stable over time and does not labilise. Thus, the effective life of the product being applied on surfaces which are not subject to dynamic movements and seismic activity, is normally in excess of 10 years. If necessary, if new discontinuities, cracklings, cracks, fissures etc. appear after the first application of Protech Balcony, these may conveniently be resolved with a second application of the product. Given its intrinsically non-pellicular nature, the product will not be subject to fissures, tears, cracks, separations, deterioration and will not yellow over time, under the effects of UV rays (as occurs naturally for epoxy and/or polyurethane treatments). The surfacings treated with Protech Balcony will be resistant to mildew, moss, lichens and other biodeteriogenic bodies. Please note that the effectiveness in terms of water repellence, and watertightness of Protech Balcony has been certified with suitable tests conducted at the laboratories of the department of structural engineering of POLITECNICO DI MILANO (the Polytechnic of Milan). Quick waterproofing, of balconies, terraces, stairs, decks, tiled surfaces, concrete structures, and natural stones, without demolishing the existing flooring. Also for use on vertical surfaces particularly exposed to the inclemency of the weather and atmospheric agents (tiled, plastered, exposed brickwork, etc.). The application surfaces should be clean, free of incrustations, crumbling and non-adhering parts, dust etc. The vanishing points between tiles, if present, should be appropriately treated with suitable acid or alkali cleaners. In this respect it is recommended that the specific acid detergent Deterg-A, diluted with water at a ratio of 1:4. Rinse the treated surfaces with running water. Labile and non-adhering vanishing points, possibly removed, are required to be restored with high adhesion and deformability cement surfacers. In this respect it is advisable to use of the specific two-component waterproof and deformable filler Stucco Balcony. Wait for the necessary time (1-2 days) for drying the filling before applying Protech Balcony. Any expansion joints present, including those relating to the junction line of the tiled flooring and the perimeter kerb (typically made of granite or natural stone), will have to be sealed with high elasticity polymeric materials. In this respect, it is advisable to seal them with Protech Flex, assisted by laying Filtene Fondogiunto and the appropriate polyurethane primer Protech Flex Primer. Pour small amounts of product at a time and spread it evenly over the entire surface with a scrubbing brush or a "water squeegee", until complete impregnation of the support to be waterproofed. Set Protech Balcony with all due care in less accessible and more uncomfortable areas, by using a brush with long bristles or a sponge (edges, skirting boards, corners, sills, wells, chimney flues, discharges, etc.). Allow the product to penetrate for at least 60 minutes. Within maximum 120 minutes of application, remove the excess product on all surfaces treated with a cloth soaked in the diluent Nitro. The product consumption is on average about 0,125 l/m² of surface to be waterproofed; varying according to the absorption of the support and the size of any vanishing points. Normally it is considered that with 1 litre of Protech Balcony you can treat from 7 to 15 m² of surfaces. Packaging: 2-liter can UM: €/l

Fluid Therm Multi-purpose Additive solution specific for the improvement of thermal conductivity of concretes, through balanced superlubricating, defoamer, plasticiser type actions. Fluid Therm is perfectly compatible in combination with steel Readymesh MM-150 (usually dosed at 25 kg/m³) or multifilament Readymesh PM-180 (usually dosed at 1 kg/m³) polypropylene fibres In radiant panel heating systems , the presence of high air content in the concrete forming the levelling screed can cause the correct spread of thermal energy to be severely obstructed; on the other hand, the conglomerate incorporates air already in the mixing phase in the form of microbubbles, while the excess mixing water and the segregation mechanisms that occur during transport and casting contribute to including additional quantities of air in the form of macrobubbles in the conglomerate. In this context, the peculiar defoamer, superlubricating and antisegregative actions of Fluid Therm, are particularly valuable as they allow the production of grouts and concretes with very low air content. Packaging: 10 kg canister UM: €/kg

Hoflader | Radlader 2,2 Tonnen Hubkraft (1,7T bei langem Hebel) - Ferrum DM416 x4 V2 Modell 2024 technische Daten Hoflader / Radlader Ferrum DM416 x4 V2 | Hubkraft Schaufel: 3.200kg | Hubkraft Palettengabel 50cm Entfernung: 2.200kg | Hubkraft Palettengabel Entfernung 60cm: 1.850kg | Leistung 40 - 60kW | Eigengewicht: 3.850kg | Allrad | Anbaugeräte - Schnellwechsler - manche Abbildungen können ggf. aufpreispflichtiges Zubehör zeigen (Anbaugeräte, Sonderbreitreifen etc.)- Unser Erfolgsmodell FERRUM DM416 x4 geht nun in 2024 in die siebte Auflage und wird von den meisten Mitbewerberprodukten in vielen nützlichen Parametern bis heute noch nicht erreicht. Wir haben in all den Jahren viel Modellpflege betrieben und so sind in Deutschland und ganz Europa mittlerweile mehrere hundert dieser multifunktionalen Baufahrzeuge im Einsatz. Zum Beginn des Jahres 2024 bieten wir Ihnen nun noch ... Art.Nr.: :Radlader_DM416_x4_V2024

Hoflader | Radlader 2,2 Tonnen Hubkraft (1,7T bei langem Hebel) - Ferrum DM416 x4 V2 Modell 2024 technische Daten Hoflader / Radlader Ferrum DM416 x4 V2 | Hubkraft Schaufel: 3.200kg | Hubkraft Palettengabel 50cm Entfernung: 2.200kg | Hubkraft Palettengabel Entfernung 60cm: 1.850kg | Leistung 40 - 60kW | Eigengewicht: 3.850kg | Allrad | Anbaugeräte - Schnellwechsler - manche Abbildungen können ggf. aufpreispflichtiges Zubehör zeigen (Anbaugeräte, Sonderbreitreifen etc.)- Unser Erfolgsmodell FERRUM DM416 x4 geht nun in 2024 in die siebte Auflage und wird von den meisten Mitbewerberprodukten in vielen nützlichen Parametern bis heute noch nicht erreicht. Wir haben in all den Jahren viel Modellpflege betrieben und so sind in Deutschland und ganz Europa mittlerweile mehrere hundert dieser multifunktionalen Baufahrzeuge im Einsatz. Zum Beginn des Jahres 2024 bieten wir Ihnen nun noch ... Art.Nr.: :Radlader_DM416_x4_V2024

Hoflader | Radlader 2,2 Tonnen Hubkraft (1,7T bei langem Hebel) - Ferrum DM416 x4 V2 Modell 2024 technische Daten Hoflader / Radlader Ferrum DM416 x4 V2 | Hubkraft Schaufel: 3.200kg | Hubkraft Palettengabel 50cm Entfernung: 2.200kg | Hubkraft Palettengabel Entfernung 60cm: 1.850kg | Leistung 40 - 60kW | Eigengewicht: 3.850kg | Allrad | Anbaugeräte - Schnellwechsler - manche Abbildungen können ggf. aufpreispflichtiges Zubehör zeigen (Anbaugeräte, Sonderbreitreifen etc.)- Unser Erfolgsmodell FERRUM DM416 x4 geht nun in 2024 in die siebte Auflage und wird von den meisten Mitbewerberprodukten in vielen nützlichen Parametern bis heute noch nicht erreicht. Wir haben in all den Jahren viel Modellpflege betrieben und so sind in Deutschland und ganz Europa mittlerweile mehrere hundert dieser multifunktionalen Baufahrzeuge im Einsatz. Zum Beginn des Jahres 2024 bieten wir Ihnen nun noch ... Art.Nr.::Radlader_DM416_x4_V2024

Hoflader | Radlader 2,2 Tonnen Hubkraft (1,7T bei langem Hebel) - Ferrum DM416 x4 V2 Modell 2024 technische Daten Hoflader / Radlader Ferrum DM416 x4 V2 | Hubkraft Schaufel: 3.200kg | Hubkraft Palettengabel 50cm Entfernung: 2.200kg | Hubkraft Palettengabel Entfernung 60cm: 1.850kg | Leistung 40 - 60kW | Eigengewicht: 3.850kg | Allrad | Anbaugeräte - Schnellwechsler - manche Abbildungen können ggf. aufpreispflichtiges Zubehör zeigen (Anbaugeräte, Sonderbreitreifen etc.)- Unser Erfolgsmodell FERRUM DM416 x4 geht nun in 2024 in die siebte Auflage und wird von den meisten Mitbewerberprodukten in vielen nützlichen Parametern bis heute noch nicht erreicht. Wir haben in all den Jahren viel Modellpflege betrieben und so sind in Deutschland und ganz Europa mittlerweile mehrere hundert dieser multifunktionalen Baufahrzeuge im Einsatz. Zum Beginn des Jahres 2024 bieten wir Ihnen nun noch ... Art.Nr.: :Radlader_DM416_x4_V2024

Hoflader | Radlader 2,2 Tonnen Hubkraft (1,7T bei langem Hebel) - Ferrum DM416 x4 V2 Modell 2024 technische Daten Hoflader / Radlader Ferrum DM416 x4 V2 | Hubkraft Schaufel: 3.200kg | Hubkraft Palettengabel 50cm Entfernung: 2.200kg | Hubkraft Palettengabel Entfernung 60cm: 1.850kg | Leistung 40 - 60kW | Eigengewicht: 3.850kg | Allrad | Anbaugeräte - Schnellwechsler - manche Abbildungen können ggf. aufpreispflichtiges Zubehör zeigen (Anbaugeräte, Sonderbreitreifen etc.)- Unser Erfolgsmodell FERRUM DM416 x4 geht nun in 2024 in die siebte Auflage und wird von den meisten Mitbewerberprodukten in vielen nützlichen Parametern bis heute noch nicht erreicht. Wir haben in all den Jahren viel Modellpflege betrieben und so sind in Deutschland und ganz Europa mittlerweile mehrere hundert dieser multifunktionalen Baufahrzeuge im Einsatz. Zum Beginn des Jahres 2024 bieten wir Ihnen nun noch ... Art.Nr.: :Radlader_DM416_x4_V2024

Hoflader | Radlader 2,2 Tonnen Hubkraft (1,7T bei langem Hebel) - Ferrum DM416 x4 V2 Modell 2024 technische Daten Hoflader / Radlader Ferrum DM416 x4 V2 | Hubkraft Schaufel: 3.200kg | Hubkraft Palettengabel 50cm Entfernung: 2.200kg | Hubkraft Palettengabel Entfernung 60cm: 1.850kg | Leistung 40 - 60kW | Eigengewicht: 3.850kg | Allrad | Anbaugeräte - Schnellwechsler - manche Abbildungen können ggf. aufpreispflichtiges Zubehör zeigen (Anbaugeräte, Sonderbreitreifen etc.)- Unser Erfolgsmodell FERRUM DM416 x4 geht nun in 2024 in die siebte Auflage und wird von den meisten Mitbewerberprodukten in vielen nützlichen Parametern bis heute noch nicht erreicht. Wir haben in all den Jahren viel Modellpflege betrieben und so sind in Deutschland und ganz Europa mittlerweile mehrere hundert dieser multifunktionalen Baufahrzeuge im Einsatz. Zum Beginn des Jahres 2024 bieten wir Ihnen nun noch ... Art.Nr.: :Radlader_DM416_x4_V2024

Hoflader | Radlader 2,2 Tonnen Hubkraft (1,7T bei langem Hebel) - Ferrum DM416 x4 V2 Modell 2024 technische Daten Hoflader / Radlader Ferrum DM416 x4 V2 | Hubkraft Schaufel: 3.200kg | Hubkraft Palettengabel 50cm Entfernung: 2.200kg | Hubkraft Palettengabel Entfernung 60cm: 1.850kg | Leistung 40 - 60kW | Eigengewicht: 3.850kg | Allrad | Anbaugeräte - Schnellwechsler - manche Abbildungen können ggf. aufpreispflichtiges Zubehör zeigen (Anbaugeräte, Sonderbreitreifen etc.)- Unser Erfolgsmodell FERRUM DM416 x4 geht nun in 2024 in die siebte Auflage und wird von den meisten Mitbewerberprodukten in vielen nützlichen Parametern bis heute noch nicht erreicht. Wir haben in all den Jahren viel Modellpflege betrieben und so sind in Deutschland und ganz Europa mittlerweile mehrere hundert dieser multifunktionalen Baufahrzeuge im Einsatz. Zum Beginn des Jahres 2024 bieten wir Ihnen nun noch ... Art.Nr.: :Radlader_DM416_x4_V2024

Hoflader | Radlader 2,2 Tonnen Hubkraft (1,7T bei langem Hebel) - Ferrum DM416 x4 V2 Modell 2024 technische Daten Hoflader / Radlader Ferrum DM416 x4 V2 | Hubkraft Schaufel: 3.200kg | Hubkraft Palettengabel 50cm Entfernung: 2.200kg | Hubkraft Palettengabel Entfernung 60cm: 1.850kg | Leistung 40 - 60kW | Eigengewicht: 3.850kg | Allrad | Anbaugeräte - Schnellwechsler - manche Abbildungen können ggf. aufpreispflichtiges Zubehör zeigen (Anbaugeräte, Sonderbreitreifen etc.)- Unser Erfolgsmodell FERRUM DM416 x4 geht nun in 2024 in die siebte Auflage und wird von den meisten Mitbewerberprodukten in vielen nützlichen Parametern bis heute noch nicht erreicht. Wir haben in all den Jahren viel Modellpflege betrieben und so sind in Deutschland und ganz Europa mittlerweile mehrere hundert dieser multifunktionalen Baufahrzeuge im Einsatz. Zum Beginn des Jahres 2024 bieten wir Ihnen nun noch ... Art.Nr.::Radlader_DM416_x4_V2024

Hoflader | Radlader 2,2 Tonnen Hubkraft (1,7T bei langem Hebel) - Ferrum DM416 x4 V2 Modell 2024 technische Daten Hoflader / Radlader Ferrum DM416 x4 V2 | Hubkraft Schaufel: 3.200kg | Hubkraft Palettengabel 50cm Entfernung: 2.200kg | Hubkraft Palettengabel Entfernung 60cm: 1.850kg | Leistung 40 - 60kW | Eigengewicht: 3.850kg | Allrad | Anbaugeräte - Schnellwechsler - manche Abbildungen können ggf. aufpreispflichtiges Zubehör zeigen (Anbaugeräte, Sonderbreitreifen etc.)- Unser Erfolgsmodell FERRUM DM416 x4 geht nun in 2024 in die siebte Auflage und wird von den meisten Mitbewerberprodukten in vielen nützlichen Parametern bis heute noch nicht erreicht. Wir haben in all den Jahren viel Modellpflege betrieben und so sind in Deutschland und ganz Europa mittlerweile mehrere hundert dieser multifunktionalen Baufahrzeuge im Einsatz. Zum Beginn des Jahres 2024 bieten wir Ihnen nun noch ... Art.Nr.: :Radlader_DM416_x4_V2024

Syntech Roadware Syntech Roadware is a high penetration two-component hybrid urethane which, combined with quartz, produces a hard and instant polymer to repair cracks and crevices in concrete floors. Syntech Roadware has a very low viscosity allowing the penetration of the product in depth, even in the narrowest cracks. It has short reaction times, in fact in 10 minutes at 20°C the material polymerizes completely and catalyzes quickly even in environments with temperatures below 0°C. It has good resistance to chemical attack. When combined with quartz powder, Syntech Roadware, forms a highly resistant compound with properties similar to existing concrete but with the flexibility that persists over time. Repair of splits or cracks in concrete, restoration of deteriorated concrete degradation, repair of cracks and pop-out phenomena in concrete. Slightly widen the crack with a circular saw to facilitate the penetration of Syntech Roadware. Before applying the product, vacuum the dust created. The support must be clean and free from dust or dirt. Apply Syntech Roadware directly on the crack or on the degraded area until the gap is completely saturated. Add quartz directly to the crack and repeat the Syntech Roadware application operation. Smooth with a spatula and leave the product to work. With a Syntech Roadware cartridge, an average of 50 linear metres of gap of 5 mm width is repaired. Bi-mix cartridge 600 ml

Syntech Pavisheer A two-component epoxy system based on epoxy resins in aqueous dispersion and solvent-free. It is ideal for completing protective, transparent treatments with a consolidating action and anti-dust effect on industrial concrete flooring, with good mechanical and chemical resistance, especially in reference to contact with oils and solvents. This product also serves well as a primer for casting joints between old and new concrete flooring. Transparent finish of interior floor coverings, mechanical-resistant impregnations, anti-dust and anti-oil for concrete surfaces. The media should have adequate mechanical resistance. The concrete surfaces should be cured, dry, planar and absorbent, free from oils, detergents, powders and soiling. The most appropriate type of mechanical preparation should also be determined (degreasing or shot peening). Conveniently absorbent surfaces may be dealt with directly after a proper cleaning. For tiled surfaces and for pre-existing coverings in resin, a degreasing or shot peening treatment is required until complete opacification and complete elimination of dust. Mix components A and B each in their own container before mixing. Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Pour component B into a suitable container and add component A. Mix everything for a few minutes using a mechanical stirrer with variable speed until a homogeneous and uniform color mixture is obtained. Leave to rest for a few minutes and mix again. Dilute the final product only with water in the Syntech Pavisheer: water ratio of 1: 3 for the first coat and 1: 2 for the second. Gradually add the dilution water, continuing to mix for a few minutes. The dilution ratio can vary according to the porosity of the support; if necessary on closed surfaces it is also possible to dilute the second coat respecting the dilution ratio 1: 3. The Syntech Pavisheer emulsion has a stability of about 2 hours at 20 ° C; within this period the product must be used. Syntech Pavisheer is applied with a short-haired roller or spray, covering the entire surface evenly. We recommend application at temperatures not lower than 5 ° C. From 0.10 to 0.15 kg of SYNTYECH PAVISHEER for each square metre of surface to be covered. Can 5 kg [A] - Canister 1 kg [A] - Can 5 kg [B] - Canister 1 kg [B] - Kit: 1 Canister 1 kg [A] + 1 Canister 1 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 5 kg [B]

Syntech Pavidamp A three-component formulation, with a fluid epoxy resin base in aqueous emulsion (A + B) to be mixed with the third component (C) consisting of white cement and micro-quartz, specially designed to be used as a primer for cementitious surfaces in the presence of humidity and in conditions of hydraulic counter-thrust. Generally referred to as “wet-bonding”, it is particularly suitable as an anti-humidity barrier for the subsequent laying of parquet. Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained. If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports. If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m². If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m². From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered. Pail 3.8 kg [A] - Pail 1.2 kg [B] - Pail 5 kg [C] - Kit: 1 Pail 3.8 kg [A] + 1 Pail 1.2 kg [B] + 1 Pail 5 kg [C]

Syntech Pavicrom SBV Colored two-component finish, permeable to water vapour, based on epoxy resins in water dispersion. Ideal for the pigmented coating of industrial floors and concrete constructions in general with residual humidity and without vapor barrier. Surfaces treated with Syntech Pavicrom SBV are easy to clean and guarantee excellent resistance to mechanical wear, as well as being highly resistant to water, alkaline solutions, detergents and hydrocarbons (petroleum, diesel, petrol, etc.) . Protective and decorative painting of concrete floors, restoration of the color of old resin floors, glazing of wall skirting boards, etc. Ideal for mechanical workshops, manufacturing industries, warehouses and factories in general where high chemical and mechanical resistance is required. It can be used both indoors and outdoors. Concrete The surfaces to be coated must be stable, clean and free of substances that could affect the adhesion of the coating. In case of restoration, use suitable mortars and products suitable for the system beforehand. Wait for the drying times before applying the next coat. The tensile strength must not be less than 1.5 N/mm². Existing paints, coatings or paints, cement grout residues, release agents, oils, greases, silicones, etc. they can be removed mechanically by sandblasting, blasting, hydroblasting or chemical removal. Cracks and fissures In case of static cracks, use Syntech Primer EP-W for sealing. The sealing of dynamic cracks or cracks larger than 4-5 mm must be assessed on site. Generally they can be grouted with elastomeric materials or act as expansion joints. Grouting and spot repairs Any holes or repairs to portions of concrete can be made with mortars from the REPAR line or by applying epoxy mortar made with Syntech Primer EP-W and quartz mastics. Apply a coat of Syntech Primer EP-W as a bonding primer, then proceed to seal and repair the damaged and broken concrete by applying the epoxy mortar. Any small filling of holes and cracks can be done by applying Syntech AS 21 epoxy mortar. Resin coatings The surfaces to be covered must be stable, clean and free of substances such as dirt, grease, oil, etc. which can affect the adhesion of the coating. Smooth the surface by mechanical sanding with diamond discs and vacuum. It is recommended to wash the surfaces and let them dry completely before applying the finish. Primer for concrete Syntech Pavicrom SBV can be applied directly to cementitious substrates as the product diluted with a maximum of 25% by weight of clean water acts as an anchoring primer. Resin coatings The application of Syntech Pavicrom SBV on resinous and multilayer systems must always be preceded by sanding the entire surface to promote and guarantee optimal adhesion of the product to the support. Combine the two components in the indicated mixing ratio. Add component B (hardener) to component A (base) and mix well until a completely homogeneous product is obtained. It is advisable to start mixing briefly with an electric drill at low speed and then intensify the stirring up to a maximum of 300-400 rpm. Leave the emulsion obtained to rest in the container, respecting the following induction times: at 15°C ~ 20 minutes at 25°C ~ 15 minutes at 30°C ~ 10 minutes The product can be applied uniformly using a spray gun or short-haired roller to avoid accumulations of material which could give rise to aesthetic defects. The application of the product must be carried out by crossing the passes and paying particular attention to the shots, regularly unloading the roller beyond the applied area to obtain a uniform film and eliminate any accumulations of product. Apply the first coat of Syntech Pavicrom SBV diluted with a maximum of 25% by weight of clean water as primer. The dilution must be carried out under mechanical stirring, adding the necessary quantity of water at the end of the induction time. Do not dilute the product further during application if it thickens it means that the use time has expired. Create a new emulsion with highly mixed material. Wait at least 12 hours, then apply the second one Colored finish diluted with a maximum of 20% weight of clean water, respecting the consumption and thicknesses indicated. It is possible to create non-slip finishes by adding quartz or hollow glass spheres. From 0.15 to 0.20 kg of Syntech Pavicrom SBV for each square meter of surface to be covered, for each coat. Pail 2.5 kg [A] - Pail 5 kg [A] - Pail 3 kg [B] - Pail 6 kg [B] - Kit: 1 Pail 2.5 kg [A] + 1 Pail 3 kg [B] - Kit: 1 Pail 5 kg [A] + 1 Pail 6 kg [B]

Syntech Epox Level Two-component coloured, high solids, self-levelling and/or multi-layer epoxy coating on concrete surfaces and cementitious substrates. Excellent mechanical and abrasion resistance Wide range of colors available Uniform, glossy finish with possible non-slip finish Excellent mechanical and chemical resistance Excellent resistance to detergents and disinfectants. ▪ Colored abrasion resistant coating ▪ Coating of floors subjected to intense traffic ▪ Coating of floors in laboratories, hospitals, sterile rooms and aseptic rooms ▪ Flooring of warehouses, shopping centres, museums, showrooms, storage and logistics areas ▪ Coating of floors of underground car parks, garages, hangars, automotive and aeronautical industries ▪ Coating of food industry floors ▪ Coating of floors in chemical and pharmaceutical industries. Self-leveling coating SYNTECH EPOX LEVEL: 1 kg/m2 QUARTZ 0.1-0.5: 0.8 kg/m2 Multilayer system 1st layer SYNTECH EPOX LEVEL: 1 kg/m2 QUARTZ 0.1-0.5: 0.8 kg/m2 + 2-3 kg/m2 for waste sowing 2nd layer SYNTECH EPOX LEVEL: 0.5 kg/m2 QUARTZ 0.1-0.5: 0.2 kg/m2 + 2-3 kg/m2 for waste sowing Finish SYNTECH EPOX LEVEL: 0.3 kg/m2 QUARTZ 0.06-0.25: 0.05 kg/m2. Can 10 kg [A] - Can 2.3 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 2.3 kg [B]

Stucco Balcony A two-component, fine cementitious grout with a fluid plastic consistency for grouting uncovered joints or filling and finishing static cracks, micro- and macro-cavities and so on between flooring tiles, before applying Protech Balcony for breathable non-film waterproofing operations on terraces and balconies. Specific putty for the preliminary preparation of supports (open gaps, micro and macro-cavities and fissures) for the subsequent application of Protech Balcony on terraces and balconies. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Add the quantity of component B required to obtain the desired consistency to component A; mix thoroughly until a homogeneous lump-free mixture is obtained. Place on site using a spatula, sponge float or simply with the fingers of the hand (wearing a rubber glove). it is possible to correct the consistency, where necessary, by adding moderate quantities of water to the ready mixture. In the cases of coloured surfacings, it is recommended to mix the two-component with small amounts of coloured pigments that can be purchased at any paint shop. Approximately 1.75 kg of Stucco Balcony for each cubic decimetre of volume to be grouted. Pail 4 kg [A] - Bucket 0.8 kg [A] - Bottle 1 kg [B] - Bucket 0.2 kg [B] - Kit: 1 Pail 4 kg [A] + 1 Bottle 1 kg [B] - Kit: 1 Bucket 0.8 kg [A] + 1 Bucket 0.2 kg [B]

Sealpvc SF 240 The SEALPVC SF 250 waterstop is a waterproof profile in PVC that is not hydro-expansive, having a thickness of 24 centimetres and high elasticity. It is used in static joints for horizontal casting (slabs), in concrete structures, resting on the substrate beneath the reinforcement. Given its particular composition, it can be cut with a sharp blade (cutter) and welded with simple heat welding tools, thus making it easier to create connections in the course of work. Waterproofing of static construction joints between: raft foundation and the elevation wall, between two raft foundations, between two elevation walls, between the wall and floor, resting on foundations under the shoring. Bind with iron wire the side flaps of the waterstop to the steel plates provided, in order to position it and secure it in a central position with respect to the casting to be made. Proceed with the casting operations, ensuring it does not bend nor move from the seat identified. 1 m/m: Use Sealpvc SF 240 welding the two edges of different belts head to head using a leister (manual hot air welder). Roll 25 m

Sealpvc RG 250 Bulb The Sealpvc RG 250 Bulb waterstop is a waterproofing PVC profile that is not hydro-expansive, having a thickness of 25 cm with a central and highly elastic bulb. It is used in dynamic joints for horizontal (slabs) or vertical (elevation walls) constructions, in concrete structures, in the central position of the cast. Given its particular composition, it can be cut with a sharp blade (cutter) and welded with simple heat welding tools, thus making it easier to create connections in the course of work. Waterproofing of the dynamic construction joints between: raft foundation and the elevation wall, between two raft foundations, between two elevation walls, between the wall and ceiling. Bind with iron wire the side flaps of the waterstop to the steel plates provided, in order to position it and secure it in a central position with respect to the casting to be made. Proceed with the casting operations, ensuring it does not bend nor move from the seat identified. 1 m/m: Use Sealpvc RG 250 Bulb welding the two edges of different belts head to head using a leister (manual hot air welder). Roll 25 m

Sanaxil I Natural, protective, decorative, breathable, pigmented, non-toxic, anti-mold plaster, with stabilized potassium silicates, for interiors and exteriors. Substantially mineral formulation which, thanks to the natural alkaline pH of potassium silicate, develops a strong antibacterial and anti-mold action. Sanaxil I is a versatile and valid product in various application fields: in green building interventions, in new constructions and in the restoration of period and monumental buildings. The product does not form a film, thus avoiding detachment and flaking phenomena and, while ensuring excellent water repellency, ensures high values of permeability to water vapor thanks to its porous and microcrystalline structure, perfectly compatible with mortars, plasters and all other common elements of the body masonry. Physical-mechanical performance and durability are coupled with a vast choice of colors that cannot be altered over time; characteristics which, combined with the ease and practicality of application, make the product extremely versatile and adaptable to any project requirement. Restoring protective coatings based on stabilised potassium silicates, for vertical and horizontal surfaces. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Existing paints (washable, organic, solvent-based etc.) must be removed. Homogenise the surfaces by applying the fixative Sanaxil Fix. Spread SANAXIL in two coats: the first, for simple deposition, with steel trowel, the second, for spreading and finishing, with sponge float. The application of the second coat must be carried out, when the first coat starts to dry, under one of two suggested conditions: with dry trowel, for smooth surfaces; with moistened trowel, for antique-effect surfaces. Sanaxil I is dry to the touch after 4 hours, it can be overcoated after 2-5 hours, while it will be dry in-depth after 16-32 hours. Indicative consumption depending on the different particle sizes of Sanaxil I available: 1 mm GRAIN: approximately 1.25 -1.40 kg/m²; 1.2 mm GRAIN: approximately 1.40 -1.55 kg/m²; 2 mm GRAIN: approximately 1.85 -2.15 kg/m²; 2.2 mm GRAIN: approximately 2.00 -2.30 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 5 kg - Pail 25 kg

Sanaxil Fix Reinforcing, fixative, transparent primer, based on stabilised potassium silicate for the preliminary treatment of the surfaces to be painted and/or plastered with silicate-based, lime putty, systems, for ecological building interventions, new buildings and for the restoration of vintage buildings and monuments. Sanaxil Fix is a product consisting of potassium silicates. It is highly breathable and is not subject to thermoplastic effects. It does not contain resins, solvents, thinners and harmful or toxic emanations. Free of V.O.C. "Priming" fixative treatment of coatings, paints or putty coat based on lime putty, potassium silicate and siloxanes in general. Dust-proofing, reinforcing, cortical treatment for surfaces of pulverising plaster. Organic type paints (washable, solvent-based etc.) where present, must be thoroughly removed. The support should, in any case, be, clean, homogeneous, compact, dust-free. SANAXIL-FIX can be applied to substrates in masonry, on cement surfaces, lime-based surfaces, on well anchored mineral paints. They can be applied by brush, roller or spray: the number of coats required and the most appropriate dilution ratio with water will be determined as a function of the absorption conditions and degradation of the support. The admissible dilution range provides for additions of water up to a maximum ratio of 1:1. Apply from 0.10 to 0.15 litres of Sanaxil Fix per square metre of surface to be treated. Plastic can 5 l - Plastic can 20 l

Sanastof A premix with a composition of breathable minerals for dehumidifying, with a base of natural hydraulic lime NHL 3.5, microsilicas with pozzolanic activity, selected aggregates, high tenacity microfibres and inert light unit weight thermal-insulating aggregates with a low elastic modulus. It is used for skimming and smoothing, both indoors and outdoors. This product is perfectly compatible with multiple substrates: lime-based plasters, lime cement, cementitious mortars, concretes, porous stone and brick. Its characteristics render it particularly suited to green building works and for restoring historic and monumental constructions. The maximum grain size of the aggregate is 0.9 mm. Sanastof is a product based on natural hydraulic lime, kaolin, marble dust, selected siliceous aggregates and lightweight aggregates with low elastic modulus, dimensionally stable. It is a natural product with high intrinsic breathability and does not have traces of resins, solvents, thinners and radioemissive aggregates. The product contains high tenacity microfibres that give great volumetric stability. The special hollow, rounded, dimensionally stable, aggregates give the skimming special thermal insulation qualities, filtration of potentially harmful soluble salts and reduction of the elastic modulus. The granulometric curve, the finesse of the binders and some natural rheological additives, make the product particularly smooth in the application phase, even when laid on supports with rough or difficult surfaces. The calibrated physical-mechanical characteristics guarantee perfect compatibility on different types of support, especially on traditional plasters and mortars. The microsilicic content of pozzolanic activity makes the skimming and the levelling performed with Sanastof extremely durable, even in aggressive exposure environments. Quick and easy application on various supports, such as: breathable finishing for wall coverings; skimming on modular insulation made of wood fibre or calcium silicate; levelling of plastered surfaces; skimming of concrete surfaces; levelling and skimming of restorations carried out with cementitious mortars; application with mainly thin thicknesses (from 1 to 4 mm) with simultaneous levelling of recesses, imperfections etc. In particularly harsh work conditions it is advisable to position the Armaglass 160 alkali-resistant fibreglass reinforcing mesh between the first and second coat (the mesh must be partially embedded in the first coat of Sanastof when it is still fresh). The breathability, combined with the other physical-chemical characteristics of the product, make the skimming carried out with Sanastof an ideal support to accommodate any kind of painting and in particular the mineral paints based on potassium silicate or lime putty. Sanastof is the breathable, low elastic modulus finish, recommended in all our dehumidifying systems carried out with: Sanatigh, Caleosana, Sanawarme, Unisan, Intosana. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc. Smooth supports should be roughed (roughness > = 1mm). If after cleaning and roughening the support is still dusty and crumbly, remove the parts completely inconsistent with spatula-brush, or by assisting the removal operation with a power wash, then consolidate the support by impregnation with Protech Fix AC aqueous emulsion applied in two abundant coats, the second coat immediately before applying Sanastof with the "fresh on fresh" technique (the consumption of Protech Fix AC for this priming operation is between 120 and 250 gr/m2). Adequately wet the support with water before application, anticipating and repeating this operation several times in case of very porous and absorbent supports or in the presence of warm and arid climates. Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Sanalink Hydraulic lime and natural light aggregate based fibre-reinforced mortar. It has high water vapor permeability characteristics, low bulk density (reduced thermal conductivity) and limited water permeability. Ideal for the construction of internal and external walls and masonry for new buildings, the renovation of existing buildings, green construction and the restoration of antique and monumental buildings. Sanalink has exceptionally strong water vapour permeability and adhesive properties and a particularly low elastic modulus. Its reduced bulk density makes it particularly advantageous in determining the thermal values ​​of the masonry, thanks to the thermal conductivity values, inferior to conventional cement mortars or lime based. It has physical, chemical and aesthetic properties very similar to antique mortars and is composed of raw materials of natural origin. The combined use of natural binders, micro-fibres and light inert pozzolanic materials guarantees high quality performance in terms of ductility, chemical resistance and water vapour permeability. It can be used for brickwork, tuff, stone and mixed masonry walls and is therefore recommended for the restoration of antique masonry, green construction and, in general, quality interior and exterior constructions. Mortar used for the construction and rehabilitation of interior and exterior masonry in solid or perforated concrete blocks, perforated bricks, solid bricks, tuff, natural stone and stone blocks in general. Application surfaces must be clean, free of dust, contamination, crumbling, inconsistencies, etc., and adequately saturated-surface-dry with water. Add approximately out 2/3 of the mixing water to the mixer and gradually add Sanalink and the rest of the water until a homogeneous, lump-free mixture of the desired consistency is obtained. The required mixing water is approximately 12-16% by weight (approximately 3.5 litres per 25 kg bag). Application can be manual (trowel) or mechanized (pumps, extruders, etc.). Approximately 17 kg/m² of Sanalink for every centimetre of thickness to be implemented (approximately 1700 kg per cubic metre). Bag 25 kg

Sanakoll Single-component adhesive-skim coat based on hydraulic lime, special flexible polymers, rheological additives, water retainers, microsilicates with pozzolanic activity, spherical aggregates with low specific weight. To be used for leveling skims on various substrates, light gluing and as skim coat/adhesive for our special SANATEX membrane (on thermal bridges, damp and/or damaged masonry). SANAKOLL is a low specific weight, low modulus of elasticity and highly breathable adhesive-skim coat. Its thermal conductivity value, < 0.2 W/mk, allows SANAKOLL to be classified in the family of thermal mortars in category T2, according to UNI EN 998/1. Its high breathability, combined with very low capillary absorption values, allows the transmission of water vapor and at the same time, thanks to special additives contained in the formula, counteracts the passage of liquid water. Its high adhesion on different types of substrates makes it the ideal skim coat/adhesive for the SANATEX membrane. The SANAKOLL-SANATEX system is used on thermal bridges, damp masonry, damaged supports, precisely by virtue of the physical-mechanical performance of the system. The smoothness of the product and its low specific weight, obtained with correct mixing with water, allows smooth, easy and fast application. SANAKOLL is a very versatile product that is also excellent for smoothing, leveling and gluing light cork elements or wood-magnesite panels. Fine-grain smoothing of lime or lime-cement based plasters and mortars. Regularization of plastered masonry up to a thickness of 5 mm applied in a single coat. Smoothing of concrete walls. Smoothing of stone elements, bricks, hollow blocks and other brick products. Adhesive-skim coat for the installation of the special SANATEX membrane, used in cold masonry (thermal bridges), in order to raise the dew point temperature of the surfaces, and in damp masonry, affected by capillary rising damp. Bonding of wood-magnesite panels, cork panels and other types of ecological modular panels, in the construction of "natural coats" (internal and external). Bonding of small-sized, medium-absorbent, non-clinkered, porous tiles and tiles on both internal and external floors and walls. The application supports must be free from dirt, dust, loose parts, etc.; pre-existing paints (washable, organic, solvent-based, etc.) must be removed. It is always advisable to operate on the application support with suitable mechanical methods capable of slightly roughening the surface, up to degrees from 3 to 5 of the ICRI methodology. Wash the surfaces with pressurized water to completely remove the dust and moisten the dry substrates immediately before applying SANAKOLL. Gradually pour about 2/3 of the mixing water into the mixer. Gradually add Sanakoll and the remaining water, continuing to mix until all lumps have been eliminated. The total percentage of mixing water is between 28% and 30% (from 7 to 7.5 liters for each 25 kg bag). The methods of use differ according to the specific intended use. For bonding on ordinary, absorbent substrates, indoors and outdoors, spread the product with a notched trowel in continuous layers, of suitable thickness, and then apply the elements to be installed (SANATEX membrane, panels, etc.), in the manner appropriate and usual, exerting the necessary pressure to promote adherence. For smoothing smoothing it is always advisable to apply two coats, waiting at least 8 hours and no more than 48 hours between the first and second coat. In particularly arid or windy climates, slightly wet the surfaces between the first and second coat. Finish the surfaces with a blade or a trowel according to the desired effect. In arid, windy or very hot conditions, it is advisable to moisten the surface of the Sanakoll applied for the first 48 hours with light and repeated nebulisations of water. Respect the minimum and maximum application temperatures. In summer, apply Sanakoll on shady supports, avoiding the hottest hours of the day. Do not apply when temperatures > 30° C are expected in the first 12 hours of maturation. In winter, do not apply the product when temperatures below 5° are expected in the first 12 hours of maturation. Do not apply when temperatures below 0°C are expected in the first 24 hours of curing. • 1.1 kg/m2 x mm of thickness. • Bonding of the Sanatex membrane, approximately 4 kg/m2 • Smoothing on Sanatex membrane, approximately 2 kg/m2. Bag 25 kg

Sanaglass Binding, vitrifying, thick, syrupy solution of natural simple molecule minerals, for the production of insulating conglomerates, based on natural powdered cork, for ecological building interventions and in the restoration of vintage buildings and monuments. For use in combination with granulated cork conglomerates for: i) implementation of walkable subbase screeds for internal use; ii) as a covering of technical installations on interior slabs in homes. Reclaim and clean the application surfaces which must be compact and hardened, free from dust, fouling etc. Mix Sanaglass thoroughly and in-depth with granulated natural cork , for an amount of approximately 80-100 kg/m³ Place on site the adhesive conglomerate thus obtained, levelling it off on the reference marks with wood supports and then compacting it with a trowel. The mixing can be done manually, as well as with a normal cement mixer. In order to facilitate the application, it is possible to use the usual pumping devices. Sanaglass is perfectly compatible with any type of granulated natural cork. If it is used in combination with a granulated cork with a particle size of between 3-8 mm (as is usually available on the market), the consumption will be roughly 80 kg/m³ (coarser granulates require a lower consumption of vitrifying substances, however it will be much less effective both with regards to trampling and to thermal and acoustic insulation). In the case of using powdered cork (diameter 0-4 mm), the dosage of Sanaglass will be in the range 110-120 kg/m³. Binder function for natural light aggregates: from 80 to 120 kg per cubic metre of conglomerate with cork granulate. Approximately 120 kg/m³ with expanded perlite. Consolidating/anti-evaporation function: 0.25 kg per square metre of surface. Pallet tank (IBCs) 1350 kg - Plastic can 25 kg